When you buy through links on our site, we may earn an affiliate commission at no cost to you.
Top 10 Rated graphtec cutter in 2023 Comparison Table
- Replacement cross cutting blade for FC8000
- Works with FC8600, FC8000, FC7000
- Fully Authorized Reseller and Only Ships Authentic Graphtec Parts
- 30 DEGREE: 30° blades are predominantly used for cutting very thin window tint and mylar materials. 45 DEGREE: 45° blades are the standard blade that comes with most vinyl cutters. They are recommended for all standard cast and calendered vinyls as well as other thin materials.
- 60 DEGREE: 60° blades are recommended for thicker materials such as reflective films, flock and twill materials and also sand-blast resist. High hardness, come with springs and blade holder base. 10 pcs for each degree.TOTAL 30 Graphtec blades.
- APPLICATION: The Hard Alloy Cutter Blades are with fine polishing process, suitable for mahogany, vinyl sheet,wood,silhouette cameo, faux leather,PVC color board, MDF and other precision relief.Compatible with Graphtec CB09U CB09 Cutting Blade Holder.
- NOTE: Our blades came with NO instructions. please do internet search and watch a few YouTube videos.Looking on YouTube will give you all the information you need to set graphtec blade up.
- AFTER SALES SERVICE: If the blade does not fit your Silhouette Cameo machine, please contact us, we will offer you full refund as we want our customers to be 100% satisfied.
- 30 DEGREE: 30° blades are predominantly used for cutting very thin window tint and mylar materials. 45 DEGREE: 45° blades are the standard blade that comes with most vinyl cutters. They are recommended for all standard cast and calendered vinyls as well as other thin materials.
- 60 DEGREE: 60° blades are recommended for thicker materials such as reflective films, flock and twill materials and also sand-blast resist. High hardness, come with springs and blade holder base. 10 pcs for each degree.TOTAL 30 Graphtec blades.
- APPLICATION: The Hard Alloy Cutter Blades are with fine polishing process, suitable for mahogany, vinyl sheet,wood,silhouette cameo, faux leather,PVC color board, MDF and other precision relief.Compatible with Graphtec CB09U CB09 Cutting Blade Holder.
- NOTE: Graphtec cb09 blades came with NO instructions. please do internet search and watch a few YouTube videos.Looking on YouTube will give you all the information you need to set graphtec blade up.
- AFTER SALES SERVICE: If CB09 CB09U graphtec blade does not fit your Silhouette Cameo machine, please contact us, we will offer you full refund as we want our customers to be 100% satisfied.
- CB09 Graphtec Blade Holder Vinyl Plotter Holder with 15pcs Blades
- Compatible with: Graphtec CB09U CB09
- With carbide materials, ultra-hardness, super toughness, more wear and edge grinding wheel with ultrafine polishing, edge sharper.
- Fine polishing process, suitable for mahogany, wood, PVC color board, MDF and other precision relief.
- Material: Hard Alloy, Degree of Blade: 30 ° / 45 ° / 60 ° (Each degree 5pcs)
- 1.Including 15pcs Cutting Blades, 5 pcs 45 degree,5 pcs 60 degree,5 pcs 30 degree. Compatible with CB09 CB09U Graphtec Cutting Blade Holder
- 2. The Blade Holder is Made of carbide materials, ultra-hardness, super toughness, more wear and edge grinding wheel with ultrafine polishing, edge sharper.
- 3. The Hard Alloy Cutter Blades are with fine polishing process, suitable for mahogany, wood, PVC color board, MDF and other precision relief.
- 4. 45°blades are the standard blade that comes with most vinyl cutters. They are recommended for all standard cast and calandered vinyls as well as other thin materials such as ThermoFlex Plus.
- 5. 30°blades are predominantly used for cutting very thin window tint and mylar materials. 60°blades are recommended for thicker materials such as reflective films, flock and twill materials and also sand-blast resist.
- 1.Compatibility - these replacement blades Perfectly compatible with Silhouette cameo (1/2/3/4)/portrait /curio and Graphtec 6000/CE 5000 -60 Plotter. Note: these Silhouette blades replacement do not automatically adjust in the silhouette for depth needed to cut, and all blades must be adjusted manually for setting depth as a continuous variable.
- 2.Including 30pcs Cutting Blades, 10 pcs 45 degree(Red Cap),10 pcs 60 degree(Blue Cap),10 pcs 30 degree(Yellow Cap). Blade Holder Compatible with CB09 CB09U Graphtec Cutting Blade Holder
- 3.Materials with ultra - hardness, carbide, super - toughness, longer wear and edge grinding with ultrafine polishing, edge more.
- 4.Application: 30 degree blade should be recommended for fabric, thin cardboard and leather, 45 degree blade used for most general purpose cuts, 60 degree blade does the most intricate and delicate cuts.
- 5.Cutting Material - these blades replacement for silhouette used for cutting card stock, fabric, heat transfer material, transparencies, paper, vellum, adhesive vinyl magnet paper.
- 45° blades are the standard blade that comes with most vinyl cutters. They are recommended for all standard cast and calandered vinyls as well as other thin materials such as ThermoFlex Plus
- Degree: 45°
- Total length: 20mm; dia.: 1.46mm
- Made from tungsten steel, coming with springs
- Quantity: Pack of 10 assorted in a plastic storage case
- Brand by AOMAG! Compatible with: Graphtec CB09U CB09
- Suitable for standard Graphtec blades 19mm (Length) x 0.9mm (Diameter)
- Aluminum-precision Vertical Adjustment
- Materials: Aluminum Alloy
- Note: Blades holder only, blades or any other accessories are NOT included!!
- PERFECTLY REPLACEMENT--No burr, no black, perfectly match with the original equipment(Graphtec Vinyl Cutter Plotter).
- HIGH-QUALITY MATERIALS--Selected hard alloy material, with super high hardness and toughness, wear resistance.
- CONVENIENT AND PRACTICAL--Small size, just 19mm, ultra-fine polished edge grinding wheel, sharp and durable.
- WIDELY APPLICATION--Cb09 graphtec blade holder base with cutting blades are suitable for stickers, PVC, reflective film, sticky notes and other materials.
- 45° BLADES--45°blades are the standard blade that comes with most vinyl cutters. They are recommended for all standard cast and calandered vinyls as well as other thin materials.
Our Best Choice: KEKAI Compatible CB09 CB09U Graphtec Blade Holder Base with 30pcs (30/45/ 60 Degree) Graphtec Blade Vinyl Cutter Plotter Cutting Blades Silhouette Cameo (30 PCS Cutter Blades)
[ad_1] CB09 Graphtec Blade Holder Vinyl Plotter Holder with 30pcs Blades
Which can help install: You can use a magnifying glass, strong light and most importantly handling the blade and spring with tweezers (which will save you sticking yourself).
How to set your depth by using a scrap of vinyl?
Using your hand to hold and pull the knife housing with the blade set to where you can hardly see it…and with a little pressure you pull it across the vinyl. Do this several times while adjusting the screw, until it does not cut the backing paper. you can laid a magazine under the vinyl to protect the table.
Please set up the depth just right. Be sure to do a depth test cut so you don’t ruin your project!just compare it to the Cameo blade and then do a test cut.
Once you’ve installed the blade, turn the button at the other end of the holder to adjust the cut thickness. unscrew the black tip, insert the blade, add the spring, screw the tip back on. The hard part is making sure the blade goes to the right place and the spring stays on.
Tips:
1. Blade should not extend too long, generally within half a millimeter is better, while paying attention to extended blade longer properly when carve the small print, in order to avoid the blade holder take the carved strokes away. Suitably engraved small print with new cutter and slow down.
2. When the word carved with angular phenomenon, you should change the blade to eliminate the problem, if the phenomenon persists after change blade, it should be the holder problem.
3. When problem arise the blade holder, try a drop of oil in the bearing and rotate the blade several times to lubricate, if still unresolved, consider replacing the blade holder.
Package Includes:
1 x Blade holder
10 x 30 Degree Cutter Blade (Yellow)
10 x 45 Degree Cutter Blade (Red)
10 x 60 Degree Cutter Blade (Blue)
30 DEGREE: 30° blades are predominantly used for cutting very thin window tint and mylar materials. 45 DEGREE: 45° blades are the standard blade that comes with most vinyl cutters. They are recommended for all standard cast and calendered vinyls as well as other thin materials.
60 DEGREE: 60° blades are recommended for thicker materials such as reflective films, flock and twill materials and also sand-blast resist. High hardness, come with springs and blade holder base. 10 pcs for each degree.TOTAL 30 Graphtec blades.
APPLICATION: The Hard Alloy Cutter Blades are with fine polishing process, suitable for mahogany, vinyl sheet,wood,silhouette cameo, faux leather,PVC color board, MDF and other precision relief.Compatible with Graphtec CB09U CB09 Cutting Blade Holder.
NOTE: Graphtec cb09 blades came with NO instructions. please do internet search and watch a few YouTube videos.Looking on YouTube will give you all the information you need to set graphtec blade up.
AFTER SALES SERVICE: If CB09 CB09U graphtec blade does not fit your Silhouette Cameo machine, please contact us, we will offer you full refund as we want our customers to be 100% satisfied.
Leave a Reply