weed eater tips

Weed control is one of the most important activities that every family needs to engage from time to time in order to maintain a decent and great lawn.

In the process of wanting to achieve all this, there is one tool that every family needs in order to clear weeds and that valuable tool is the weed eater echo.

However, it should be noted that the weed eater echo is a machine that runs on fuel, and that fuel is not a charity donation but one that is bought by your hard-earned money.

This fact that the weed eater runs on gas behooves homeowners to device means and come up with strategies that will enable them to get optimum service from these weed eaters by making optimal use of costly fuel.

One of the best and easiest ways of achieving optimal fuel consumption is through the adjustment of the carburetor.

This article therefore seeks lay out an elaborate outline of how you can do this under different circumstances in order to attain an optimal combination of air and fuel.

Matters altitude

The altitude of your home may affect the performance of your weed eater echo. This is because the carburetor needs a good supply of air in order to function well.

However, it is important that you check the air filter and clean off all the residues.

You need to clean the spark arrestor screen and ensure that the trim lines and cutting head are all in their correct length.

You can confirm the correctness of their length by ensuring that the lines stretch their way to the blade on the deflector. After getting through with each of these stages, ignite the engine and give it some time to warm up.

At higher sea levels

On the side of your weed eater echo, locate the screws that are used to adjust low and high speed respectively.

Turn these screws anticlockwise in order to achieve a decent level of restricting the flow of air into the carburetor and in turn this restriction will supply extra fuel.

In order to attain optimal results and correct setting, you may be required to adjust the screws as much as possible.

Higher altitudes

In places with higher altitude, your weed eater echo only needs a lean mixture of that will provide the engine with a low amount of fuel.

You will need to turn the high and low speed adjustment screws left to right in order to achieve the above results.

For you to attain an optimal mixture of fuel, you will be required to adjust the screws until they reach their extreme end.

Dealing with matters of idleness

You can change the trimmer’s idling speed through the adjusting of the carburetor in order to optimize its functionality.

To do this, you will need to get to the screw that adjusts the idle speed and then change its positioning in accordance with idling issues at hand.

Irregularity with idling speed

When the mixture of fuel in the weed eater echo is very lean, it may lead to the irregularity of the weed eater’s idling or it may even interfere with the weed whacker’s proper acceleration.

In such cases, you will need to turn the low speed adjusting screw anticlockwise till the engine regains its normal acceleration.

When the engine cuts off during idling

In cases where the weed eater’s engine goes off while the trimmer is idling, you need to make adjustment to the idle speed.

You will need to idle speed adjusting screw left to right until the engine regains smooth running.

Read more related product reviews

• Best Cordless Electric Weed Eater
• Best Corded Electric Weed Eater
• Best Gas Weed Eater
• Best Weed Wacker Reviews
• Best Push Lawn Mower

The Weed Eater

Your average weed eater is a simple shaft with a rotating head with plastic string that spins at a high velocity and trims lawns and they are usually powered by either gas or electricity (corded or battery powered).

Having a weed eater is really convenient because they can do things that a lawn mower can’t do, not to mention they are a lot lighter too.

Any homeowner or professional landscaper definitely needs a string trimmer if they hope to keep their lawn and garden looking great.

Some string trimmers aren’t just string trimmers though, much of the time they can do a lot more.

This is done through various attachments that can blow leaves, cultivate dirt, edge lawns, and the thing we are here to talk about today, trimming the hedges.

The Hedge Trimmer Attachment

Hedge trimmers are really great tools too.

Alongside a string trimmer this is one of the other main tools that any landscaper should have in their arsenal because it means that you don’t have to use a big pair of bush scissors to cut those giant hedges!

It just makes the job so much better and easier.

Even better is when you can use the string trimmer to do the lawn and then simply switch the trimmer head out for a hedge trimmer.

It means that you don’t have to buy 2 separate tools to get the job done; all you have to do is switch out the attachments!

What To Look Out For When Getting A Hedge Trimmer Attachment

The first thing that you need to consider when you get the attachment is what kind of string trimmer you have.

On a side note if you are looking to add on attachments like a hedge trimmer then you probably want to have a gas powered string trimmer because they provide a lot more power and versatility than your electric ones.

That being said when you buy the hedge trimmer attachment you may need to buy a smaller version if you have an electric powered one.

Ok, so now that’s out of the way, something else that you want to look out for is how long the trimmer is; the longer the trimmer is the easier your job will be because it cuts more at once.

On the other hand you also have to consider the weight of the attachment. The bigger the attachment is the heavier the item will be.

The other thing to consider is what material the hedge trimmer teeth are made out of; you want to get a harder metal or else the teeth will break when it hits something a little thicker.

How To Attach The hedge Trimmer

Attaching the head trimmer isn’t too difficult.

Most string trimmers that come ready for attachments will either have a simple clipping or screw on system so can easily unscrew or unclip the string trimmer and put on the hedge trimmer attachment in a flash.

Always keep in mind that each model is different though so you will always want to read the owner’s manual however they all usually just screw or clip.

Safety Precautions

Something to keep in mind when purchasing a hedge trimmer attachment for your weed eater is that they are slightly dangerous and if you are not careful there is a possibility of injury.

This is especially the case if the equipment is too heavy and the user loses control of it, thus always make sure that you buy a machine and attachment that is light enough to handle safely without injury of any kind.

Here’s a short instructional video:

Read more related product reviews

• Best Cordless Electric Weed Eater
• Best Corded Electric Weed Eater
• Best Gas Weed Eater
• Best Weed Wacker Reviews
• Best Push Lawn Mower

A weed eater engine on bike is just one of the many solutions that this machine offers to the lives of millions.

It does not only empower a weed eater to mow down annoying weeds buy it can also be used in empowering your tired or slow moving bike to greater heights of speed and efficiency.

Mounting a weed eater engine on bike is not just fun but also a creative and simple way of exploiting the many uses and benefits of this engine.

Additionally, mounting a weed eater engine on a bike is a very economical process that does not require any special or extra economic muscle.

In terms of complexity, the process gets even much better because it is a simple process that anyone can undertake without having to acquire any special rocket science.

To complete the icing on the cake, the process of mounting a weed eater engine on bike is something that you can commence and finish within a day as long as you follow the clear and simple instructions laid down in this article.

So, what does it take to mount a weed eater engine on bike? What are the benefits of using a weed eater engine to make a motorized bike as opposed to buying a new one from the shop?

First of all, it will save you many dollars that you would have spent on a new motorized bike.

To get started, you will only need a bike, a weed eater motor with a clutch, a tensioner, wheel sprocket, a welder, bike brake cables, and metal mounting straps.

Once you have all these in place, follow the process below and get to mount your weed whacker engine on a bike. 

Prepare the frame

Before everything else, get the frame ready for the mounting by removing its rear wheel.

Next, mount a large sprocket to the left side of the bicycle. This sprocket will be connected to another one smaller one using around eleven teeth.

The smaller sprocket will be welded to the motor clutch with a gear ration of 18 to 1 between the two sprockets.

Make sure that the ratio is not too low so that the engine is not ruined.

Build the engine mount

Next, you need to mount the weed eater engine in the most suitable place that you have elected.

The most popularly preferred areas are behind the bicycle saddle or beneath the center bar.

After this, you can fix the straps in the most ideal place that you have chosen.

Depending on the kind of straps that you have, you can either choose to weld them in a fixed place or bolt them onto the frame if they have holes at their ends.

Mount the engine

Make sure that the straps are tight enough not to allow the engine to keep shifting as you ride your motorized bike. As you mount he engine, make sure that it is facing the right direction.

Attach the chain

After you are through with the mounting of the engine, it is now time for you to attach the chain, placing it between the sprockets. After the attachment, make sure that you bolster the sprocket ring with the help of a tensioner.

Rebuild the brakes

Now that you have the engine, chain and every other thing in place, you need to make sure that the brakes are rebuilt.

This means that you will be required to rewire the brakes so that you can be able to control the speed and movement of the bike properly.

You will first of all need to remove the brake cable and with the help of a metal end stop to attach the cable to the carburetor throttle again.

If the old brake cable is short, use a spare cable to attach it to the throttle.

Read more related product reviews

• Best Cordless Electric Weed Eater
• Best Corded Electric Weed Eater
• Best Gas Weed Eater
• Best Weed Wacker Reviews
• Best Push Lawn Mower